Table of Contents
One of the most famous Briggs & Stratton engines is the Intek v Twin.
This engine is used in various outdoor power equipment, including lawn mowers, pressure washers, and generators.
While the Intek v Twin is a reliable engine, some common problems can occur.
Here are some of the most common issues with the Briggs & Stratton Intek v Twin engine.
Oil Leaks
One of the most common problems with the Briggs & Stratton Intek v Twin engine is oil leaks.
If you notice oil leaking from your engine, it is vital to take action right away. The first thing you should do is check the oil level and make sure it is correct.
If the oil level is low, you will need to add more oil.
If the oil level is correct, you will need to check for leaks. The most common place for leaks is at the gasket between the cylinder and the crankcase.
If you find a leak at the gasket, then you will need to replace it.
Engine Knock
Another common problem with the Briggs & Stratton Intek v Twin engine is engine knock. It is a knocking noise that can be heard when the engine is running.
Engine knock is caused by the pistons hitting the cylinders.
If you hear an engine knocking, it’s best to act immediately. The first thing you should do is check the oil level and make sure it is at the correct level.
If the oil level is insufficient, you’ll need to add more oil.
If the oil level is correct, you will need to check the spark plugs. And make sure they are clean and in good condition.
If the spark plugs are fouled or damaged, they need to be replaced.
Hard Starting
If you own a Briggs & Stratton Intek v Twin engine, you may have experienced the problem of hard starting.
It is when the engine is difficult to start or it takes a long time to start. There are a few reasons why this can happen.
One reason is that the spark plug may be dirty or damaged. If the spark plug is not functioning correctly, it will be difficult for the engine to start.
Finally, if the air filter is clogged, it can also cause a tricky starting. If you’re experiencing this problem, check these three things first.
With some troubleshooting, you can get your Intek v Twin engine running smoothly again in no time.
Surging
Surging is a common problem with Briggs & Stratton Intek v Twin engines. The engine speed fluctuates, or the engine seems to be revving up and down on its own.
Several factors can cause it. It includes a dirty air filter, a problem with the carburetor, or an issue with the ignition system.
In most cases, surging can be fixed by cleaning the air filter, adjusting the carburetor, or replacing the spark plugs.
However, if the problem persists, it is best to take the engine to a certified Briggs & Stratton dealer.
Burning Oil
The Briggs & Stratton Intek v Twin engine is a popular choice for small engines, but it’s not without problems.
One common issue is that the engine can burn through oil faster than expected. There are a few reasons why this can happen.
One reason for burning oil could be that the piston rings are worn. If the piston rings are worn, they will need to be replaced.
Another reason for burning oil could be that the valves are sticking. If the valves are sticking, they will need to be replaced.
Overheating
Overheating is another typical problem with the Briggs & Stratton Intek v Twin engine. It occurs when the engine becomes too hot and stops operating.
There are a few causes for this to occur.
The cooling fins might be clogged, which is one sign of excessive heat. If the cooling fins are dirty, they will need to be cleaned.
The Briggs & Stratton website has a helpful video on how to do this.
Another cause of overheating could be the oil being too thick. If the oil is too thick, it will need to be replaced.
The Briggs & Stratton website also has a helpful video on how to do this.
If neither of these solutions solves the overheating problem, Briggs & Stratton recommends contacting a qualified service dealer.
Noisy Engine
Briggs & Stratton Intek v Twin engines are known for being quite noisy. It is because the engine design amplifies sound, making it seem louder than it is.
In addition, the Briggs & Stratton Intek v Twin engine uses a lot of fuel. It causes the engine to run rough and make more noise than usual.
There are a few reasons why this can happen.
One reason for a noisy engine could be that the valve clearance is too tight. If the valve clearance is too tight, it will need to be adjusted.
Another reason for a noisy engine could be that the piston rings are worn. If the piston rings are worn, they will need to be replaced.
There are a few things that you can do to reduce the noise from your engine.
First, make sure that the engine is properly lubricated. It will help to reduce friction and noise.
Second, make sure that the muffler is in good condition and properly installed. It will help to reduce the amount of noise that the engine makes.
By following these simple tips, you can help to reduce the noise from your Intek v Twin engine.
Vibration
Vibration is another common problem with the Briggs & Stratton Intek v Twin engine. A certain amount of vibration is to be expected with any engine.
But the Briggs & Stratton Intek v Twin often vibrates more than it should.
It can be caused by many factors, including incorrect installation, an imbalanced flywheel, or a damaged crankshaft.
There are a few reasons why this can happen.
One reason for vibration could be that the engine mounts are loose. If the engine mounts are loose, they will need to be tightened.
Another reason for vibration could be that the crankshaft is out of balance. If the crankshaft is out of balance, it will need to be replaced.
Sometimes, simply tightening the bolts that secure the engine to the frame can reduce vibration.
However, if the problem persists, it may be necessary to replace the flywheel or crankshaft.
With proper care and maintenance, Briggs & Stratton Intek v Twin can provide years of dependable service.
However, as with any engine, it is essential to be aware of common problems to address them quickly and efficiently.
Key Takeaways
- Briggs & Stratton Intek v Twin engines are known for being quite noisy.
- Briggs & Stratton Intek v Twin engines often vibrate more than they should.
- Common problems with Briggs & Stratton Intek v Twins include burning oil, overheating, noisy engines, and vibration.
- These problems can be caused by several factors, including incorrect installation, an imbalanced flywheel, or a damaged crankshaft.
With proper care and maintenance, Briggs & Stratton Intek v Twins can provide years of dependable service.
However, it is essential to be aware of common problems so they can be addressed quickly and efficiently.
