You just got a new Delton AR 15. You’re excited to take it to the range, but when you try to fire it, nothing happens. You rack the slide and pull the trigger, but still nothing. What’s going on?
It’s possible that you’re experiencing one of the most common Delton AR 15 problems. In this article, we’ll walk you through the most common problems and how to solve them.
Delton AR 15 Problem: Delton AR 15 Is Too Tight
The first common problem is that the Delton AR 15 can be too tight. This means that it’s hard to pull the charging handle back and it’s tough to chamber a round.
There are a few things you can do to solve this problem. The first is to try using a lubricant on the bolt carrier group.
You can also try buffing out the contact points on the upper and lower receiver with some fine grit sandpaper. If those solutions don’t work, you might need to loosen the barrel nut a bit.
Delton AR 15 Problem: Forend Is Wiggle
Your Delton AR-15 forend is loose and wiggles. You tighten the screws but it keeps coming loose.
There are a few things you can do to fix this problem:
First, make sure that the screws are tight. They should be tight enough that they don’t move when you tug on them, but not so tight that they strip the screw head.
If the screws are tight and the forend is still wiggling, then you may need to use a thread locker to keep them in place.
A thread locker is a type of adhesive that will keep the screws from loosening over time.
If the screw heads are stripped, then you will need to replace the screws with ones that have a bigger head.
The most common charging handle issue is that it doesn’t stay in place. It pops out and makes it difficult to cock the rifle. There are a few things you can do to fix this:
Use Loctite on the screw that holds the charging handle in place
Make sure the screw is tight
Put a rubber band around the charging handle and the receiver
Delton AR 15 Problem: Safety Selector Switch Not Working
If your safety selector switch isn’t working, it could be because the switch itself is faulty or because the disconnector spring is not engaged.
To fix this, you’ll first want to check the switch to see if it’s working properly. If not, you can try replacing it with a new one. If the problem persists, then it’s likely that the disconnector spring is not engaged.
To fix this, you’ll need to remove the safety selector switch and then re-engage the disconnector spring. Once you’ve done this, your safety selector switch should be working properly.
Delton AR 15 Problem: AR 15 Trigger Reset Issues
If you’re having problems with your Delton AR 15 trigger resetting, there are a few things you can try.
First, check to see if the problem is with the trigger itself or with the hammer. If it’s the trigger, you’ll need to replace it. But if it’s the hammer, you can try polishing it.
If that doesn’t work, you may need to adjust the sear engagement. This is something you should only do if you’re experienced with working on firearms, as it’s easy to mess up and make the problem worse.
Finally, if you’re still having issues, you can try changing out the springs. This is again something that should only be done by someone who knows what they’re doing, as improper installation can cause serious problems.
Delton AR 15 Problem: AR 15 Magazines Not Feeding Properly
This is a common problem with AR 15s, and there are a few possible causes. The first thing you want to check is the magazine. If it’s damaged or bent, that could be causing the issue.
Another possibility is that the magazine release is not engaged all the way. This can happen if you’re using an aftermarket magazine release that’s not compatible with your AR 15.
Finally, it could be an issue with the bolt catch. If the bolt catch is not engaged all the way, it can cause feeding problems.
If you’re having this problem, the best thing to do is to take your AR 15 to a gunsmith and have them take a look at it. They’ll be able to diagnose the problem and get your rifle back up and running in no time.
Delton AR 15 Problem: Your Gun’s Finish Is Wearing Away
If you’ve noticed that the finish on your Delton AR 15 is wearing away, it’s probably because you’re using the wrong cleaning products.
To fix this, you’ll want to switch to using a mild soap and warm water to clean your gun.
Make sure you rinse it well and dry it thoroughly afterwards. You can also use a lubricant on the metal parts of the gun to protect the finish.
If the finish is already damaged, you can try refinishing it yourself or taking it to a gunsmith.
This is a pretty easy process, but it’s important to make sure you do it right so that the new finish will last.
Delton AR 15 Problem: The Trigger Pull Is Too Heavy
If the trigger pull on your Delton AR 15 is too heavy, there are a few things you can do to fix it.
One is to install a lighter trigger return spring. This will reduce the amount of force required to pull the trigger, making it easier to shoot.
Another option is to install a lighter hammer spring. This will help reduce the amount of force required to cock the hammer, making it easier to fire the gun.
Finally, you can install a lighter buffer spring. This will help reduce the amount of force required to cycle the action, making it easier to fire the gun.
Delton AR 15 Problem: The Gun Jams Frequently
You’re out on the range, blasting away at some targets. You’re having a great time, until all of the sudden your Delton AR 15 jams. This is a common problem with guns, and can be frustrating to deal with.
There are a few things you can do to try and fix the jam. The first is to make sure that you’re using the correct ammunition for your gun.
The second is to make sure that you’re cleaning your gun regularly. And the third is to check the firing pin and make sure that it’s in good condition.
If none of these solutions work, it might be time to take your gun into a gunsmith and have them take a look at it.
Conclusion
All in all, if you’re having problems with your Delton AR 15, there are a few things you can do to try to fix them.
First, check the gas key to make sure it’s tight. If it is, then you may need to disassemble the rifle and clean it thoroughly. If that doesn’t work, you may want to take it to a gunsmith to have it checked out.
